Hardware ( 16MB RAM/ 4MB FLASH, AR7 MIPS32 CPU )
* Marvell 88E6060 - 6-Port Fast Ethernet Switch
* P2V28S40BTP - Mira P2V28S40BTP (4-BANK x 2,097,152-WORD x 16-BIT DRAM)
( 128Mbit / 8 bit words = 16MB DRAM )
* 29LV320MBTC - MXIC 32Mbit, 4Mx8 single voltage 3V only flash memory ( 4MB FLASH ).
* TNETD7200 - TI AR7 CPE Solution ( MIPS32 RISC core, ADSL front-end, 2x16550 UART, USB ) (local PDF)
* TNETW1350A - TI Application-Specific Single-Chip MAC and Baseband Processor (local PDF)
* Some kind of RF Front-End, probably TNETW3428 and TNETW3422
How to connect JTAG and UART to WAG200 system board
Marcin Baliniak discovered location of WAG200 JTAG and UART ports. Here are the pictures and some information about these ports:
1 - JTAG, 2 - UART ( it's under the barcode sticker ).
Here are Marcin's picture of soldered in JTAG and UART connectors:
Layout of the connectors:
JTAG UART
nTRST 1 2 GND 1 GND (black wire on the photo)
TDI 3 4 GND 2 TX (white wire on the photo)
TDO 5 6 GND 3 Vcc (red wire on the photo)
TMS 7 8 GND 4 RX (blue wire on the photo)
TCK 9 10 GND
nSRST 11 12 n/a
n/a 13 14 Vcc
Software features
* ADAM2 boot loader
* Linux kernel version 2.4.17 ( in Linksys version 1.00.07 )
* squashfs filesystem for main software image
* 64Kb, flash based NVRAM ( as in ohter ADAM2 based devices )
* precompiled, binary-only kernel modules for AR7, DSL, WLAN and onboard LED's.
Diagnostic commands output, and dumped flash partitions
Here's the output from various diagnostic commands ran on the device with original fimware:
# ls /dev/mtdblock/
/dev/mtdblock/0 /dev/mtdblock/2 /dev/mtdblock/4
/dev/mtdblock/1 /dev/mtdblock/3 /dev/mtdblock/5
# cat mtd
dev: size erasesize name
mtd0: 002d0000 00010000 "mtd0"
mtd1: 000b0000 00010000 "mtd1"
mtd2: 00020000 00010000 "mtd2"
mtd3: 00010000 00010000 "mtd3"
mtd4: 00010000 00010000 "mtd4"
mtd5: 00040000 00010000 "mtd5"
# cat cpuinfo
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 211.35
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
# cat sys/dev/adam2/environment
maca 00:14:bf:6f:81:b2
macb 00:14:bf:6f:81:b3
memsize 0x01000000
flashsize 0x00400000
modetty0 115200,n,8,1,hw
modetty1 115200,n,8,1,hw
bootserport tty0
cpufrequency 211968000
sysfrequency 105984000
bootloaderVersion 0.22.02
ProductID WAG200G
HWRevision Unknown
SerialNumber none
my_ipaddress 169.254.87.1
prompt WAG200G
firstfreeaddress 0x9401bd20
req_fullrate_freq 125000000
mtd0 0x900d0000,0x903a0000
mtd1 0x90020000,0x900d0000
mtd2 0x90000000,0x90020000
mtd3 0x903e0000,0x903f0000
mtd4 0x903f0000,0x90400000
mtd5 0x903a0000,0x903e0000
oam_lb_timeout 100
# cat partitions
major minor #blocks name
31 0 2880 mtdblocka
31 1 704 mtdblockb
31 2 128 mtdblockc
31 3 64 mtdblockd
31 4 64 mtdblocke
31 5 256 mtdblockf
# cat meminfo
total: used: free: shared: buffers: cached:
Mem: 14581760 12328960 2252800 0 1191936 4251648
Swap: 0 0 0
MemTotal: 14240 kB
MemFree: 2200 kB
MemShared: 0 kB
Buffers: 1164 kB
Cached: 4152 kB
SwapCached: 0 kB
Active: 1060 kB
Inactive: 5336 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 14240 kB
LowFree: 2200 kB
SwapTotal: 0 kB
SwapFree: 0 kB
# cat tty/driver/serial
serinfo:1.0 driver:5.05c revision:2001-07-08
0: uart:16550A port:A8610E00 irq:15 baud:7944 tx:6225 rx:0 RTS|DTR
1: uart:unknown port:A8610F00 irq:16
# cat wlan/hal/acxParams
-------- ConfigOptionsFixed ----------
NVSVersion = 04 1b 06 00 12 00 00 06
ProductId =
ManufactureId =
dot11MacAddress = 00:00:53:90:2c:dc
ProbeDelay = 17
EndofMemory = 0x1010104
dot11CCAModeSupported = 0
dot11DiversitySupport = 5
dot11ShortPreambleOptionImplemented = 1
dot11PBCCOptionImplemented = 6
dot11ChanneAgilityPresent = 0
dot11PHYType = 2
dot11TempType = 1
-------- ACX100 elements ----------
AntennaList (0) =
SupportedPowerLevels (2) = 0x1e00 0xa00
SupportedDataRates (5) = 0x02 0x04 0x11 0x22 0x44
SupportedRegDomains (0) =
# ps -ef
PID Uid VmSize Stat Command
1 root 288 S init
2 root SW [keventd]
3 root SWN [ksoftirqd_CPU0]
4 root SW [kswapd]
5 root SW [bdflush]
6 root SW [kupdated]
7 root SW [mtdblockd]
29 root 196 S /usr/sbin/download
43 root 220 S /usr/sbin/utelnetd -p 23 -d
45 root 224 S /sbin/klogd
55 root 484 S wpa_auth
65 root 284 S /sbin/syslogd -f /etc/syslog.conf
74 root 176 S /usr/sbin/ntp -t 3600 -z GMT-8
81 root 252 S /usr/sbin/mini_httpd -d /www -r Linksys WAG200G -c *
88 root 224 S /usr/sbin/crond
90 root 172 S /usr/sbin/scfgmgr
92 root 204 S /usr/sbin/atm_monitor
96 root 168 S /usr/sbin/cmd_agent_ap
97 root 168 S /usr/sbin/pb_ap
98 root 160 S /usr/sbin/wizd
116 root 716 S /usr/sbin/upnpd nas0 br0 30 4
118 root 348 S -sh
119 root 716 S /usr/sbin/upnpd nas0 br0 30 4
120 root 716 S /usr/sbin/upnpd nas0 br0 30 4
122 root 716 S /usr/sbin/upnpd nas0 br0 30 4
123 root 716 S /usr/sbin/upnpd nas0 br0 30 4
124 root 716 S /usr/sbin/upnpd nas0 br0 30 4
142 root 716 S /usr/sbin/upnpd nas0 br0 30 4
21465 root 416 S -sh
21993 root 292 R ps -ef
# lsmod
Module Size Used by
tiap 843072 1
led
3880 0
push_button 1544 1
tiatm 122440 0
----------------